When Should I seal my new wood deck?

The wood on a new deck needs to dry thoroughly before sealing or staining. If the wood came still wet with preservative, allow it to dry about 30 days before applying stain or sealer. To test the wood to see if it’s dry enough to stain or seal: Pour a little water on the wood.

On the same token, if the water beads up and sits in round bubbles on the surface of the wood, your deck doesn’t need to be sealed and was either sealed recently or is made of pre-treated wood. The other way you can tell if your wooden deck needs sealing is if you notice bubbling and cracks in the sealant.

Also Know, when Should I seal my new cedar deck? If you are looking to preserve the beautiful rich grain of, say, a mahogany or cedar decking, we recommend sealing the deck with a translucent penetrating stain within 1-2 weeks of construction. This will ensure minimal or no UV damage and give your deck that natural look.

Accordingly, how long do you have to wait to seal pressure treated wood?

It is important to wait for the wood to dry before sealing a new deck, but at the same time, you don’t want to wait too long. Drying can take several months. We recommend beginning to test the wood around 90 days after your project is completed, but this is just a general suggestion.

Is it better to stain or seal a deck?

Surfaces such as decks, wood siding, fences, and so on need a protective coating to keep from weathering so fast. A deck sealer is typically a clear or transparent finish that either penetrates into the wood or forms a clear film on top. A deck stain has the same water-resistant qualities that a deck sealer does.

What is the best way to protect a wood deck?

Protect the investment in your wooden desk by taking these 10 preventive measures: Don’t trap dirt. Catch that grease. Sweep it up. Shovel it off. Clean and seal regularly. Take special steps for a new deck. No matter the age, always make sure your deck is sealed. Even pressure treated wood needs to be sealed.

What is the best deck sealer?

The Top 8 Best Deck Sealers for 2020 are: DEFY Extreme Semi-Transparent Exterior Wood Stain. Thompson’s WaterSeal Advanced Natural Wood Protector. #1 Deck Premium Semi-Transparent Wood Stain. Tall Earth Eco-Safe Wood Treatment. DeckWise Ipe Oil Hardwood Deck Finish. Ready Seal Natural Cedar Exterior Wood Stain and Sealer.

What is the best exterior wood stain?

Best Exterior Wood Stains in March, 2020 Wood stain Colors 1 Defy Extreme Editor’s Choice 7 2 Ready Seal 7 3 #1 Deck Premium 4 4 Thompson’s WaterSeal Stain 5

Do I have to seal my deck after pressure washing?

After completing the deck power washing, wait 24 to 36 hours before applying sealer. If the weather is cool or humid, wait 48 to 72 hours. The deck must be thoroughly dry to ensure deep penetration of the sealer.

What goes on first stain or sealer?

We’re using a wipe-on oil finish as the sealer. The key is to apply a thin base coat to partially seal the wood before wood staining. Sanding sealers, dewaxed shellac and wipe-on finishes will all do the trick. If the wood was sealed completely, it would be difficult to get any stain to stick.

Can you spray Thompson’s Water Seal?

Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. Once you are done with the product, it is recommended that you run mineral spirits through the sprayer and then water to clean it.

Can you put Thompson Water Seal on treated wood?

Wolman RainCoat, made by one of the big names in pressure-treating, is a widely sold water repellent that is a good choice for use on pressure-treated wood, although it can also be used on other types of wood. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.

Is it better to stain or paint pressure treated wood?

Staining treated wood Not only can you stain treated wood, staining and painting pressure treated wood is actually good for your new deck. Although the treated wood doesn’t need to be protected against rot, staining it will help reduce surface cracking.

What is the best sealer for treated wood?

Here are some of the best deck sealers on the market: Thompsons Waterseal Advanced Natural Wood Protector. ECO-SAFE Wood Treatment – Stain & Preservation by Tall Earth. Rust-Oleum Coppercoat Wood Preservative. CabotStain Australian Timber Oil Penetrating Oil. Thompsons Waterseal – Transparent Stain.

What happens if you paint pressure treated wood too soon?

Because it is not thoroughly dry, new pressure treated lumber can quickly warp and bend if you don’t handle it correctly. After you buy new pressure treated lumber, build with it right away, or keep it stacked flat in a dry place and wait at least 60 days to four months before painting it.

How can I determine if pressure treated wood is ready for staining?

To determine if your treated wood is ready for stain, simply flick a little bit of the stain onto the wood in a small spot. If the stain bubbles up on the wood, you are not ready to stain. If the stain soaks in, you’re ready to stain. After two weeks, my deck was ready for stain.

How do you know if wood is dry enough to stain?

One way to measure if the deck is dry enough for staining is by using a moisture meter. A moisture meter measures the amount of moisture in the wood. There are one to two probes on the meter that stick into the wood to give you a reading. If using this method, be sure to check the moisture level in several spots.

Do you need to seal cut pressure treated wood?

Use Cut-N-Seal® on areas that have been drilled or saw cut in treated wood deck boards, railing, post tops, fence boards, etc. Cut-N-Seal is not recommended to replace pressure treatment. Do not use to recoat pressure treated wood surfaces.