What is a roofing starter strip?

A starter strip is an asphalt based shingle utilized to waterproof the eave and rake edges of your home during a re-roof. Adhesive tar strips help prevent shingle blow-off from harsh winds (along eaves as well). A straight line to properly orient each new row of shingles.

Ideally, starter shingles used should be specially made to be used as starter. These starter shingles will have a tar strip on the bottom to help hold the edges of the roof down and prevent blow-offs. Also, the best starter shingles to use should run at least 2″ up the roof under the bottom of the second shingle.

Subsequently, question is, how do starter shingles work? Starter shingles are the initial shingle products installed on the roof, just before the first course of the finish shingles, which will comprise the visible parts of the roof. Each Leading Edge Plus starter strip “shingle” is perforated right down the middle so that you get two starter strips out of each roof shingle.

Also question is, how long is a starter shingle?

1. Starter Strip is packaged two pieces per shingle, 16 shingles per bundle, 105 lineal feet. 2. Perforation down the center allows for easy separation.

How far should shingles overhang drip edge?

The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.

Do you remove the plastic strip on shingles?

No, leave the strip alone: In answer to a common reader question, not normally: according to roofing manufacturers, it is not required to remove the cellophane strip on the back of roof shingles before they are nailed.

How many starter shingles do I need?

Overview. Owens Corning® Starter Strip Shingle helps save time by eliminating the need to cut shingles to create a starter row. It is packaged two pieces per shingle, 16 shingles per bundle. The continuous sealant ensures an effective seal between the starter and the first course of shingles.

Can you replace drip edge without removing shingles?

Now, generally it’s replaced at the same time your shingles are replaced, but really it’s fairly easy to replace it anytime. The shingles along the lower edge of the roof are gently lifted up, so as not to damage them, and then a flat pry bar is used to remove the nails holding the eave strip to the decking.

What goes on roof before shingles?

Before the shingles are ever nailed onto the roof, a layer of felt paper is applied to the wood sheathing. The felt paper on top of the sheathing acts as a moisture and vapour barrier for your roof. That’s essential, because rain and moisture can actually get under your shingles.

How do you nail shingles?

NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8″ diameter heads, long enough to penetrate through plywood or 3/4″ into boards. Use 4 nails per shingle placed 6-1/8″ above the butt edge, 1″ and 13″ in from each end and 1/2″ above each cutout.

What is a cap shingle?

The shingles at the peak of your roof are commonly called cap shingles. If your shingles are standard three-tab shingles, the caps are made by cutting one shingle into three separate parts. The overall size of most cap shingles is 12 inches by 12 inches.

How do you install drip edge?

Installing roof drip edge flashing properly Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.

How many feet does a bundle of cap shingles cover?

33.3 sq. ft

How many feet of starter are in a bundle?

Now there’s no reason to cut down 3-tab shingles to use as a starter strip. In addition, the continuous sealant ensures an effective seal between the starter and the first course of shingles. Starter strip shingles are packaged 2-pieces per shingle, 16 shingles per bundle, 100 lin. ft.

What does step flashing look like?

Step flashing can be made with aluminum, copper, lead, galvanized steel, or stainless steel, but most commonly it is aluminum or copper. Small L-shape flashing pieces must be woven into the shingles as you work your way up the roof. The flashing integrates the roof cladding into the wall cladding to keep water out.