# How can we calculate tolerance value of resistors?

The tolerance band is silver, so we multiply our resistance by 0.1. This means that our resistor’s value can be as high as 16.5 Ω or as low as 13.5 Ω. For the third resistor, we’ll perform the calculation in an alternative way. Take the nominal value and multiply it by 1 + your tolerance, which is (1+0.1).

Also know, what are the colors of resistors?

Components and wires are coded with colors to identify their value and function. The colors brown, red, green, blue, and violet are used as tolerance codes on 5-band resistors only. All 5-band resistors use a colored tolerance band.

What is a resistor color code?

An electronic color code is used to indicate the values or ratings of electronic components, usually for resistors, but also for capacitors, inductors, diodes and others. A separate code, the 25-pair color code, is used to identify wires in some telecommunications cables.

How do you read a resistor color code?

Steps
1. Position the resistor with the gold or silver color band to the right..
2. Read the color sequence that must be decoded to determine resistance.
3. Determine the coded number for the resistive value.
4. Determine the tolerance of the resistor.
5. Determine the decoded number for the resistive value.

## What are the colors of resistors?

Components and wires are coded with colors to identify their value and function. The colors brown, red, green, blue, and violet are used as tolerance codes on 5-band resistors only. All 5-band resistors use a colored tolerance band.
Resistors are blind to the polarity in a circuit. Thus, you don’t have to worry about installing them backwards. Current can pass equally through a resistor in either direction. In schematic diagrams, a resistor is represented by a jagged line, like the one shown in the margin.
A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.
Devices called resistors let us introduce precisely controlled amounts of resistance into electrical circuits. Photo: Four typical resistors sitting side by side in an electronic circuit. A resistor works by converting electrical energy into heat, which is dissipated into the air.

## What is a resistor color code?

An electronic color code is used to indicate the values or ratings of electronic components, usually for resistors, but also for capacitors, inductors, diodes and others. A separate code, the 25-pair color code, is used to identify wires in some telecommunications cables.
220R / 220 ohm Resistor Colour Code
Value 220 Ω
Type 4 Band Colour Code System
Colour Code Red, Red, Brown, Gold
Multiplier Brown, 10
Tolerance Gold Band ±5%

## Why is there a difference between the measured value and the nominal value of the resistors?

The actual (measured) resistance will vary from the nominal value due to subtle mechanical and chemical differences that occur during manufacturing. The manufacturer specifies the maximum deviation from the nominal value as a ±percentage. This range of deviation is called the tolerance of the resistor family.

## What is resistor and its use?

A resistor is an electrical component that limits or regulates the flow of electrical current in an electronic circuit. Resistors can also be used to provide a specific voltage for an active device such as a transistor.
10R / 10 ohm Resistor Colour Code
Value 10 Ω
Type 4 Band Colour Code
Colour Code Brown, Black, Black, Gold
Multiplier Black, 1
Tolerance Gold Band ±5%

## What is the use of a carbon resistor?

Carbon Resistors. The most common type for electronics use is the carbon resistor. They are made in different physical sizes with power dissipation limits commonly from 1 watt down to 1/8 watt. The resistance value and tolerance can be determined from the standard resistor color code.

## What is a resistor made up of?

Resistor composition. Resistors can be constructed out of a variety of materials. Most common, modern resistors are made out of either a carbon, metal, or metal-oxide film. In these resistors, a thin film of conductive (though still resistive) material is wrapped in a helix around and covered by an insulating material.
The assembly yield is the quality level. It is the percent of assemblies which meet the engineering tolerance requirements. It is calculated by summing the component tolerances to determine the assembly variation, then applying the upper and lower spec limits to the calculated assembly distribution.

## What is the color code for a 100k ohm resistor?

100k / 100k ohm Resistor Colour Code
Value 100 kΩ
Type 4 Band Colour Code System
Colour Code Brown, Black, Yellow, Gold
Multiplier Yellow, 10000
Tolerance Gold Band ±5%

## What is percentage of tolerance?

Percent of tolerance. Percent of tolerance is calculated by taking the measurement error of interest, such as repeatability and/or reproducibility, dividing by the total tolerance range, then multiplying the result by 100 to express the result as a percentage.

## What is the meaning of tolerance in resistor?

Tolerance is the percentage of error in the resistor’s resistance, or how much more or less you can expect a resistor’s actual measured resistance to be from its stated resistance. A gold tolerance band is 5%tolerance, silver is 10%, and no band at all would mean a 20% tolerance.” Source: Resistor Color Codes.

## What is Colour coding in safety?

Safety Color Coding Labels and Tape
COLOR MEANING
Fluorescent Orange, Orange-Red Biosafety
Yellow Caution
Orange Warning
Green Safety
Orient the resistor so you can read the stripes properly. You should read the stripes from left to right. The first stripe is the one that’s closest to one end of the resistor. If this stripe is on the right side of the resistor, turn the resistor around so the first stripe is on the left.
If I understand your question, then yes – resistors are reversible, in the sense that they can be connected to the circuit in either direction. Resistors are not like diodes or capacitors. They do not have a polarity. The conduct (or resist) current equally in both directions of current flow.